In small computer room, weak current room, industrial control cabinet, corridor weak current box and other scenes with limited space, din-rail type fiber optic terminal box with the advantages of small, convenient and flexible installation, become the core device of fiber fusion, fiber core protection, tail fiber management.

                       HT2005-DR-12LCD

Din-Rail type fiber optic terminal box, also known as rail-type fiber optic fusion box, distribution box, the core definition is: A small optical fiber management device that can be installed in standard DIN guide rails. It is mainly used for fusion, fiber core fixing, tail fiber storage and jumper docking of a small number of optical fibers (usually 12 cores and below). It is compact in size and easy to install. It does not need to occupy a lot of space. It is perfectly suitable for small wiring scenarios with limited space. It fills the gap of large ODF wiring equipment in small networking. It is an indispensable core component in small and medium-sized optical communication wiring.

Compared with traditional wall-mounted and desktop fiber optic terminal boxes, the core advantage of Din-Rail type fiber optic terminal boxes lies in "adapting to small scenes and flexible installation". It adopts standard DIN rail installation design, which can be directly installed on the rail of control cabinet or weak current box together with circuit breaker, switch and other equipment without additional punching and fixing. It has high installation efficiency and clean layout. It is compact in size, usually less than 100mm in width, and highly adaptable to rail installation space. It is suitable for space-tight scenes such as corridor weak current box, industrial control cabinet and small machine room. At the same time, it has good dustproof and moisture-proof performance to protect the internal fiber core from environmental erosion.

The structure design of the Din-Rail guide type optical fiber terminal box is simple and practical, and the core consists of three parts: fusion area, storage area and interface area. A small fusion tray is built in the fusion zone, which can realize precise fusion of 1-12 core fiber and tail fiber, ensuring low fusion loss and stable signal; the storage area is compact in design, which can orderly store the residual fiber and tail fiber, avoiding fiber breakage or signal attenuation caused by cable clutter and pulling; the interface area can be installed with mainstream fiber adapters such as SC and LC, realizing flexible docking of tail fiber and jumper, supporting single mode and multimode fiber adaptation, and meeting different transmission requirements.

Din-Rail type fiber optic terminal box has a wide range of application scenarios, and the core is suitable for small networking and terminal points. In FTTH fiber-to-the-home scenario, it can be installed in the corridor weak current box to realize the fusion of optical cable branch and home optical fiber, which is compact and does not occupy space; in industrial scenario, it can be installed in the control cabinet to adapt to the optical fiber connection and protection of industrial equipment, anti-interference, high and low temperature resistance; in small room and weak current room, it can be used for terminal management of a small number of optical fibers, and can be installed in cooperation with other equipment to improve space utilization; In the security monitoring scene, it can be installed near the monitoring point to realize the fusion and tail fiber management of the camera fiber, which is convenient for later maintenance.

Following core points should be paid attention to when selecting guide rail type fiber optic terminal box:

Firstly, capacity, according to the number of fiber cores to choose 1 core, 4 core, 8 core, 12 core and other specifications, to avoid capacity waste or insufficient;

Secondly, the protection performance, outdoor or wet scenes need to choose IP54 and above protection level, indoor scenes can choose IP20 level;

Thirdly, material and quality, high-quality products using flame retardant ABS or metal materials, high precision welding plate, can ensure low welding loss, long service life,

Fourthly, Select the correct fiber type, such as single-mode G.652D, G.657A1/A2, multimode OM1/OM2/OM3/OM4, etc.;

Fifthly, Select the correct optical fiber interface, such as LC, SC, FC, etc.

H&T’S HOTCOM brand Din-Rail type fiber optic terminal box can be fully linked with its own fiber jumper, adapter and other products to avoid transmission hidden dangers caused by device incompatibility. At the same time, it supports customized specifications and can adjust interface types and capacities according to scene requirements. Whether it is fiber optic home, industrial networking or security monitoring, it can provide efficient fiber core management solutions, which are trusted by engineers and operation and maintenance personnel.

Our products have been applied in large projects at home and abroad, such as BASF chemical industry, urban rail transit, electric power, Coal mines, wind power  and other scenes, stable and reliable running, worry-free after-sales, welcome system integrationeng&ineering friends to negotiate&purchase!

pls add us at whatsapp: +86 15712000724 for more details and discounts